| Fire Retardant |
|---|
Firepro FR29 is highly effective on natural and most synthetic fibres.
FR29 is a highly effective, economical, easy to use fire retardant.
It has been used in New Zealand sinse 1988.
FR29 was formulated primarily for fire protecting, to AS1530:3, carpet used on walls in passageways and lifts in hotels and institutional buildings and cotton, acrylic cotton blend, and hessian fabric draped from ceilings and walls in restaurants, and exhibitions, etc where fire testing to AS1530:2 is required.
Datasheet FR29 |
Products such as Hessian, Coir, Canvas and heavy Drapes have an indicative requirement of 0.2 Litres/M2.
As a general rule 0.1 Litres of FR29 per 100grams of fabric with a minimum of 0.1 Litres per M2 will give good results. |
 |
| Intumescent Coatings for Steel |
|---|
Firepro PST-100 is a water-borne coating for the fire protection of internal (weather protected) structural steel which enables the steel to be highlighted as a feature of the building design.
Additionally, the intumescent system is often the most cost effective method of fulfilling the fire rating requirements of the steel.
Datasheet PST-100 |
Colour: White
VOC: 75g/Litre
Fully tested to BS476 Part 21 for up to two hours fire protection. |
|
| TopSeal Coatings for Steel |
|---|
Firepro C622 is a high quality single pack modified alkyd topcoat for use over Firepro intumescent coating for the fire rating of structural steel.
This topseal is not in itself a fire protective coating.
C622 is a coating formulated to provide chemical, abrasion and weather resistance.
C622 is available in gloss and semi-gloss and metalic finishes. Stocked in white gloss.
May be tinted to BS colours.
Datasheet C622
SHELF LIFE: Up to 12 months if stored in unopened containers in cool dry conditions.
THEORETICAL COVERAGE: 8 square metres per litre. DFT 40µm
DRYING TIMES: At 25°C allow 4-8 hours before recoating. |
|
Firepro C623 is a high quality single pack 100% pure acrylic finish coat approved for use as part of Firepro Intumescent Coating Systems for the fire rating of structural steel.
This topseal is not in itself a fire protective coating.
C623 is a coating formulated to provide chemical, abrasion and weather resistance.
Datasheet C623 |
C623 is available in gloss and semi-gloss finish, stocked in white gloss, may be tinted to BS colours. |
|
Firepro C624 is a high quality, two pack,UV protected, interior/exterior coating with a very hard and durable finish, for use over Firepro C963, C608 and C609 intumescent coatings for the fire rating of structural steel.
This topseal is not in itself a fire protective coating.
Datasheet C624 |
COVERAGE RATE: 6-8M2 per litre per coat 1 coat minimum 2 coats for exterior applications. |
|
| High Performance Coatings for Steel |
|---|
Firepro C626 Firepro C626 is a 2 pack epoxy zinc rich primer providing exceptional corrosion resistance in harsh exposures.
Recommended for use over abrasive blast cleaned steel surfaces in most harsh environments.
Datasheet C626 |
Provides good corrosion protection in servere weather conditions.
Quick turn around time for applicators, very rapid cure for epoxy.
Suitable for use in high temperature environments.
Excellent durability, abrasion, chemical & solvent resistant. |
|
Firepro C627 is a red primer giving corrosion protection in one coat. This steel primer is not in itself a fire protective coating.
Datasheet C627 |
|
|
Firepro C628 Fast drying high quality red oxide single pack zinc phosphate alkyd primer for corrosion protection of steel.
Steel should be overcoated with intumescent basecoat within 3 days.
This steel primer is not in itself a fire protective coating.
Datasheet C628 |
|
|
Firepro C963 is an intumescent coating system for the protection of structural steel that enables the steel to be highlighted as a feature of the building design.
C963 combines final decoration of steel with its fire protection.
Datasheet C963 |
Use Firepro C963 to achieve 30, 60 or 90 minutes Fire Resistance. Overcoat with Firepro Topseal to colour finish. |
|
| Intumescent Coating for Timber |
|---|
Firepro C640 is a clear intumescent coating primarily for use on internal timber based products.
Datasheet C640 |
When applied to timber panelling and similar timber products, delays ignitability, spread of flame and reduces smoke, assisting people to escape from a burning building. |
|
Firepro C646 is a water-borne intumescent coating for use on internal non-combusible surfaces.
Datasheet C646 |
Recommended for interior use only.
PACK SIZE - 4 litre and 10 litre. |
|
| Intumescent Coating for Cables |
|---|
Firepro C696 is an aqueous intumescent fire retardant coating for cables with plastic casing, to reduce the danger of spread of fire along the cables.
Datasheet C696 |
|
|
| Structural Steel Protection |
|---|
Cafco 300 is a gypsum/vermiculite based spray used to fire protect structural steel.
It can be pumped in its slurry form for over 100M to the point of application.
It is delivered to site in powder form and mixed with water to form a slurry in the spray machine.
Datasheet Cafco 300 |
White textured finish, can be trowelled flat. |
|
